Event File Format
Event files (extension *.evt) contain triggers and events and can be loaded as an additional file to provide more information about the whole course of an EEG/MEG recording. An event file can be edited by opening it in any text editor, e.g. Notepad. It is also possible to create new event files from scratch which can be imported into the data file later. Note the following conventions for event files:
- Event descriptions are given in the columns of the event file
- Each file must contain a header line and data lines
File Header
The header is comprised of abbreviated descriptions for each column. Each entry in the data line must be specified in the header line at the correct column position. The order of the data elements and their description in the header line can be chosen arbitrarily and the entries can be separated by commas, tabs and/or spaces. The last n data elements can be omitted, if they are neither Code nor one of Tms, Tmu or Tsec. The following codes are recognized by the ERP module:
- Code - event code (integer, see section Event Codes)
- Tms - event time in milliseconds relative to the start of the data file or Tmu [in microseconds] or Tsec [in sec] (floating point value)
- TriNo - trigger number (integer) (identifies the trigger in the event bar of the main module)
- RCode - reaction code (integer)
- RTms - reaction time in milliseconds or RTmu or RTsec (floating point value)
- Comnt - comment to describe event (string of up to 39 characters), will be truncated if longer than 39 characters.
You can also define columns which should not be recognized by the ERP module. Simply specify these columns in the header with any unknown code. Therefore you might be able to use previously generated files without major changes.
Event Codes
The event code Code must be one of the following integers:
| Code | Event/Trigger Type |
|---|---|
| 1 | Trigger |
| 2 | Comment |
| 3 | Marker |
| 11 | Pattern1 |
| 12 | Pattern2 |
| 13 | Pattern3 |
| 14 | Pattern4 |
| 15 | Pattern5 |
| 21 | Artifact on |
| 22 | Artifact off |
| 31 | Epoch on |
| 32 | Epoch off |
| 41 | New segment |
| 42 | Average segment |
Additional Event Information
The event reaction time, event reaction code and event comment are represented by the comment in the main module as "Comment (Rx,T____)", where Comment is the event comment, x describes the reaction code and the underscored line will be filled with the reaction time. Reaction time and reaction code are only read if the event code specifies it as a trigger. A "New Segment" event can include time information that defines the starting time of the segment. This is defined in the TriNo column of the event file. The format is YYYY-MM-DDTHH:MM:SS, e.g. 2010-04-26T15:30:20.31 (note: seconds are a decimal number). If no time is defined, use a hyphen ('-'). See below) for an example. An "Average Segment" includes the prestimulus baseline interval in microseconds. This is defined in the TriNo column of the event file.
Requirements
The file is valid if the header line contains at least the entries Code and one of Tms, Tmu and Tsec. The header specifications are case insensitive. The file is invalid, if • there are ambiguities in the header • there is a data type mismatch in the data line • an event time specifies an event which happened later than the end of the acquisition Each omitted data entry is set to 0 or empty string by default. A line with an invalid or unknown event code Code is skipped.
Examples
Here are a couple of typical examples:
1.) Simple trigger file
| Tms | Code | TriNo | Comnt |
| 100.234 | 1 | 3 | Trigger: 3 |
| 2300.456 | 1 | 1 | Trigger:1 |
| 4500.21 | 1 | 1 | Trigger:1 |
| 9800.47 | 1 | 7 | Trigger:7 |
| 12500.78 | 1 | 2 | Trigger:2 |
| 21237 | 1 | 1 | Trigger:1 |
This example event file can be downloaded here: File:EventFileExample1.evt
2.) Trigger file with reaction code and reaction time
| Tms | Code | TriNo | RTsec | RCode |
| 100.234 | 1 | 3 | 0.23 | 1 |
| 2300.456 | 1 | 1 | 1.11 | 2 |
| 4500.21 | 1 | 1 | 0.15 | 1 |
| 9800.47 | 1 | 7 | 0.87 | 0 |
| 12500.78 | 1 | 2 | 2.1 | 2 |
| 21237 | 1 | 1 | 3 | 1 |
This example event file can be downloaded here: File:EventFileExample2.evt
3.) Event file without triggers
| Tmu | Code | Comnt |
| 10000.234 | 3 | Marker |
| 230000.456 | 12 | |
| 450000.21 | 14 | |
| 980000.47 | 12 | |
| 1250000.78 | 3 | Marker |
| 2123700 | 2 | Comment |
| 2534100.567 | 15 |
This example event file can be downloaded here: File:EventFileExample3.evt
4.) File including triggers and events
| Tms | Code | TriNo | RTsec | RCode | Comnt |
| 100.234 | 2 | 0 | 0 | 0 | CommentSet |
| 2300.456 | 1 | 2 | |||
| 4500.21 | 1 | 1 | 0.15 | 1 | |
| 9800.47 | 11 | ||||
| 12500.78 | 3 | ||||
| 21237 | 2 | 0 | 3 | 1 | Comment |
| 25341.567 | 15 |
This example event file can be downloaded here: File:EventFileExample4.evt
5.) New Segments
| Tms | Code | TriNo | Comnt |
| 0 | 41 | 2010-04-26T15:30:20.31 | Start recording |
| 21000 | 41 | 2010-04-27T09:17:00.0 | Next day |
The new segment at the time 0 overrides the start time in the file. A second segment at 21 s starts a new data block one day later at 9:17.
This example event file can be downloaded here: File:EventFileExample5.evt
6.) Average Segments
| Tms | Code | TriNo | Comnt |
| 0 | 42 | 100000 | Cond 1: 25 avs |
| 1100 | 42 | 200000 | Cond 2: 201 avs |
The file contains two average segments. The first, with a prestimulus interval of 100 ms, has a duration of 1100 ms. The second, with a prestimulus interval of 200 ms, has a length up to the end of the data file.
This example event file can be downloaded here: File:EventFileExample6.evt
